Our Chemicals
Browse our range of industrial and specialty chemicals
Showing 81–100 of 356 products
Agricultural Mulch Film Compound (UV Stabilised)
A UV-stabilised biodegradable compound for mulch film designed to be tilled into the soil at the end of the season instead of lifted and landfilled. The stabiliser package sets how long the film lasts in the field.
Pet Waste Bag Compound (High Toughness)
A high-toughness biodegradable blown film compound for pet waste bags, where a thin gauge must not fail in use. It is formulated for toughness and puncture resistance at low film thickness in a fully biodegradable system.
PLA/PBAT/Starch Ternary Blown Film Compound
A ternary pellet compound of PLA, PBAT and starch for general-purpose biodegradable blown film. The starch fraction lowers the resin cost and raises renewable content, at some cost in mechanical performance.
High Barrier Co-extrusion Film Compound (PLA/PBAT)
A PLA/PBAT pellet compound formulated for the barrier layer of a co-extruded biodegradable film structure. It is specified where shelf life depends on controlling moisture or oxygen transmission through the pack wall.
Heat Shrink Film Compound (PLA/PBAT)
A biodegradable PLA/PBAT pellet compound for blown shrink film, formulated to give controlled shrinkage in a heat tunnel. Shrink onset temperature and shrink ratio are set to fall within the window a standard tunnel runs.
Paper-Plastic Lamination Compound (PLA/PBAT)
A PBAT-based pellet compound with PLA for extrusion coating and lamination onto paper and board. It gives a moisture or grease barrier that does not make the substrate unrecyclable as conventional polyethylene coating does.
Ultra-Thin Water-Permeable Mulch Film Compound
A biodegradable pellet compound for very thin mulch film that lets applied water through to the soil rather than shedding it. It suits irrigation regimes that water over the film rather than through buried drip line.
Diaper Backsheet and Composite Film Compound (PLA/PBAT)
A PLA/PBAT pellet compound for the backsheet layer of absorbent hygiene products, where a soft, quiet, liquid-tight film is required. It is also formulated for the lamination step that bonds the film to the nonwoven outer.
Bubble Film and Bubble Mailer Compound (PLA/PBAT)
A blown film grade PLA/PBAT pellet compound for biodegradable bubble film and padded mailers, run on standard lines. It is formulated to survive bubble forming and then to hold air in the bubble over time.
Cutlery Injection Compound (PLA + Mineral Filler, FDA, 85C)
A mineral-filled PLA injection grade for disposable cutlery, rated to 85C so a fork does not soften in hot food. The filler adds the stiffness a knife needs to cut, and the compound is FDA compliant for food contact.
Disposable Cup, Bowl and Plate Injection Compound (FDA)
An FDA-compliant biodegradable injection grade for rigid disposable tableware, formulated for thin-wall flow across a large part. Where the item will hold hot food, the heat-resistant container grade should be specified instead.
Chopstick Injection Compound (FDA)
An FDA-compliant biodegradable injection grade for moulded chopsticks, formulated for the stiffness and surface finish a long, slender part requires. It is an alternative to both moulded polystyrene and single-use timber.
High Flow Injection Compound for Small Cases
A high-flow biodegradable injection grade for small precision housings and cases, where surface finish on a visible part is the governing requirement. It fills detailed cavities cleanly and needs no secondary finishing.
Cosmetic Bottle Blow Moulding Compound (FDA)
A biodegradable PLA/PBAT blow moulding grade for cosmetic and personal care bottles, formulated for the melt strength a hanging parison needs and for even wall distribution. It is supplied FDA compliant for contact applications.
Toothbrush Handle Injection Compound
A biodegradable PLA/PBAT injection grade for toothbrush handles and similar personal care bodies, supplied as a pellet compound. It is formulated for rigidity and moisture resistance in months of daily wet use.
Coffee Capsule Injection Compound (95C, FDA)
An FDA-compliant biodegradable injection grade rated to 95C, supplied as a heat-modified PLA pellet compound. It is made for single-serve coffee capsules that must hold their shape under pressurised hot water extraction.
Cold Use Food Container Injection Compound (PLA/PBAT, FDA)
An FDA-compliant PLA/PBAT injection grade for rigid cold-use food containers, such as chilled deli, salad and dessert packs. It is formulated for clarity, stiffness and impact resistance at refrigerated temperatures.
Hot Use Food Container Injection Compound (80C, Microwaveable, FDA)
An FDA-compliant biodegradable injection grade rated to 80C and microwaveable, supplied as a heat-modified PLA/PBAT pellet compound. It is for hot food containers and ready meal packs that are filled hot or reheated.
Nursery Pot and Tray Compound (Compostable)
A compostable PLA/PBAT compound for nursery pots and propagation trays, supplied as pellets for thermoforming or injection moulding. Its service life is matched to the crop cycle rather than left open-ended.
Fibre-Reinforced Flower Pot Compound
A natural-fibre reinforced biodegradable injection compound for decorative and retail flower pots, supplied as pellets. It gives both the stiffness a full pot needs and the matt, natural appearance retail buyers want.